INTERNATIONAL TRUCK & ENGINE CORPORATION: Safety Recalls in 2000

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE VEHICLES INVOLVED IN THIS RECALL WERE BUILT FOR EXPORT WITH MANUAL SLACK ADJUSTERS AND WERE SOLD IN THE US. THESE VEHICLES NEED TO HAVE AUTOMATIC SLACK ADJUSTERS IN ORDER TO COMPLY WITH THE REQUIREMENTS OF FMVSS 121, "AIR BRAKE SYSTEMS."

VEHICLE DESCRIPTION: SCHOOL AND HEAVY DUTY TRUCKS EQUIPPED WITH TRW DRAG LINKS. EACH DRAG LINK ASSEMBLY CONTAINS TWO 20-EDL MODEL BALL SOCKET ASSEMBLIES. CERTAIN OF THE BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET.

VEHICLE DESCRIPTION: TRUCKS EQUIPPED WITH ALLISON 1000 OR 2400 SERIES TRANSMISSIONS. THESE TRANSMISSIONS CAN EXPERIENCE PARK PAWL TO REAR COVER INTERFERENCE DUE TO AN OUT OF FLATNESS CONDITION.

VEHICLE DESCRIPTION: TRANSIT BUSES BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU). THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL.

VEHICLE DESCRIPTION: SCHOOL BUSES BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU). THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL.

VEHICLE DESCRIPTION: MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU). THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL.

VEHICLE DESCRIPTION: TRACTORS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU). THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL.

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE BRAKE LIGHT SWITCH AND THE CRUISE CONTROL SWITCH ARE MOUNTED IN SUCH A WAY AS TO ALLOW MOISTURE WITHIN THE AIR BRAKE SYSTEM TO COLLECT INSIDE THE SWITCHES. IF THE MOISTURE IN THE SWITCHES FREEZES, THE BRAKE LIGHTS MAY NOT FUNCTION AND THE CRUISE CONTROL MIGHT NOT DISENGAGE WHEN THE BRAKE PEDAL IS DEPRESSED.

VEHICLE DESCRIPTION: SCHOOL AND HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS. THE ABS SENSOR WIRES ON ROTATING PARTS CHAFES WHICH CAN LEAD TO A FALSE SIGNAL BEING SENT TO THE BENDIX ABS ELECTRONIC CONTROL UNIT (ECU).

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH EATON AUTOSHIFT GEN II TRANSMISSION ASSEMBLIES. DUE TO A SOFTWARE PROBLEM IN THE TRANSMISSION ASSEMBLIES, THE TRANSMISSION WILL SELECT THE WRONG GEAR.

VEHICLE DESCRIPTION: SCHOOL/TRANSIT BUSES AND MEDIUM DUTY TRUCKS. THE CASTINGS USED ON THE POWER STEERING PUMPS WERE NOT BUILT TO MATCH THE ENGINEERING DRAWINGS, RESULTING IN A THIN WALL IN THE PUMP CASTING OR A COMPLETE CONNECTION OF TWO PASSAGES THAT ARE SUPPOSED TO BE SEPARATED TO CONTROL FLUID FLOW. THE FLUID FLOW MAY BE REDUCED TO LESS THAN THE MINIMUM REQUIRED FLOW RATE TO PROVIDE FULL POWER ASSIST TO THE BRAKE SYSTEM WITH LOW ENGINE SPEED.

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL CODE 16SCH (LOWER BUNK WEBBING RESTRAINT). INCORRECT BOLTS WERE USED TO HOLD THE BUNK WEBBING RESTRAINT LATCH BRACKETS TO THE BUNK BASE.

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE ANTILOCK TRACTION RELAY VALVES WERE INCORRECTLY ASSEMBLED BY THE SUPPLIER. AN EXTRA CHECK VALVE WAS INSTALLED WHICH WILL NOT ALLOW THE TRACTION CONTROL SYSTEM TO FUNCTION PROPERLY.